Deep Throat.
Deep Throat.
Trying to get one that'll take at least 6 inches but the cost is ridiculous, not that keen on purchasing a cheaper option in case things buckle under pressure.
So if any one knows of a good strong deep throat "G-CLAMP" for a reasonable cost could you please tell me.
So if any one knows of a good strong deep throat "G-CLAMP" for a reasonable cost could you please tell me.
Effluent in many languages.
Re: Deep Throat.
Can't beat carver clamps, and I've had some good buys off car boot sales.
"Land Rover, the worlds best 4x4 by far"
"Argo, a great 8x8"
"Argo, a great 8x8"
Re: Deep Throat.
Carvers are the dogs but i'v never seen one 6" deep?
Chas search for 'record' on ebay mate. The older ones will be far better than todays stuff
For new reasonably priced brands 'babco' arent too bad. I'v not broken one of mine yet and used them on some fairly heavy jobs, couple of them have lost the swivel foot though of course
Chas search for 'record' on ebay mate. The older ones will be far better than todays stuff
For new reasonably priced brands 'babco' arent too bad. I'v not broken one of mine yet and used them on some fairly heavy jobs, couple of them have lost the swivel foot though of course
Re: Deep Throat.
Cheers Rod and Adam.
Been searching for all sorts and the prices are stupid if you want the good stuff, even second hand are fetching quite a sum.
I have a load of clamps but need one or two with a bit more throat on em to hold a router jig in place, which sounds quite simple until you not only want to hold the jig on to the wood but then clamp it all to a bench and I don't have a bench that shallow.
Making a new bench is going to be much cheaper I'm now thinking, the jig concerned is only 370mm long so need a small sticky out bench just that bit wider.
I'm a metal man by trade and this wood lark is starting to pee me off a bit
Thanks.
Chris.
Been searching for all sorts and the prices are stupid if you want the good stuff, even second hand are fetching quite a sum.
I have a load of clamps but need one or two with a bit more throat on em to hold a router jig in place, which sounds quite simple until you not only want to hold the jig on to the wood but then clamp it all to a bench and I don't have a bench that shallow.
Making a new bench is going to be much cheaper I'm now thinking, the jig concerned is only 370mm long so need a small sticky out bench just that bit wider.
I'm a metal man by trade and this wood lark is starting to pee me off a bit
Thanks.
Chris.
Effluent in many languages.
Re: Deep Throat.
Wood is annoying as feck at times mate. If i cut a piece of steel too short i can just weld a bit back on
I measured once cut twice and the damn things still too short!
I measured once cut twice and the damn things still too short!
- Fox Hunter
- Posts: 1036
- Joined: 15 Oct 2011, 18:20
- Location: Wales
Re: Deep Throat.
I just googled six inch deep throat....I don't think the results were very helpful
Re: Deep Throat.
Yeah but you werent looking for clampsFox Hunter wrote:I just googled six inch deep throat
- Fox Hunter
- Posts: 1036
- Joined: 15 Oct 2011, 18:20
- Location: Wales
Re: Deep Throat.
Erm...no...not when I saw the results anywaysunndog wrote:Yeah but you werent looking for clampsFox Hunter wrote:I just googled six inch deep throat
Re: Deep Throat.
Totally innocent mistake on my part, honestly.
I couldn't understand why when I went to check my post, some 5 seconds after hitting the submit button, it had already been viewed 6 times.
How are you James ?
I couldn't understand why when I went to check my post, some 5 seconds after hitting the submit button, it had already been viewed 6 times.
How are you James ?
Effluent in many languages.
Re: Deep Throat.
Nipple clamps obviously go with a six inch deep throat.
I'm amazed that Rod gave a straight answer to the original question. Is that a sign of the apocalypse?
Anyone know if Record tools are still made in the UK? It appears that Irwin have bought them out and Irwin brand tools have shit quality now that they are made in China.
I'm amazed that Rod gave a straight answer to the original question. Is that a sign of the apocalypse?
Anyone know if Record tools are still made in the UK? It appears that Irwin have bought them out and Irwin brand tools have shit quality now that they are made in China.